The following Q&As have been taken from the Answers & Analysis Online Search Engine. Access to this Online Education just one example of the many benefits of becoming an IAPMO Member. For more details about IAPMO membership go to www.iapmomembership.org

Shower Valves
Subject: Shower Valves
Section: 408.1 (2021 UPC)
Question: Does a prefabricated shower listed to IAPMO IGC 154 means the shower valve meets the minimum requirement for an individual control valve of the pressure balance, thermostatic, or combination pressure balance/thermostatic mixing valve type that provides scald and thermal shock protection for the rated flow rate of the installed showerhead and installed at the point of use complying with ASSE 1016/ASME A112.1016/CSA B125.16 or ASME A112.18.1/CSA B125.1?
Answer: Yes, IAPMO IGC 154, Section 4 General requirements, 4.2 Plumbing Components, 4.2.1.1 and 4.2.1.2 make direct reference to the two standards and content applicable to each standard.
Shower Control Valves
Subject: Shower Control Valves
Section: 408.3 (2021 UPC)
Question: Is there a distance or proximity that a shower valve must be from the entrance?
Answer: No, the 2021 UPC Section 408.9 Location of Valves and Heads. Control valves and showerheads shall be located on the sidewall of shower compartments or otherwise arranged so that the showerhead does not discharge directly at the entrance to the compartment so that the bather can adjust the valves before stepping into the shower spray.
Waterproofing Membranes
Subject: Waterproofing Membranes
Section: 301.2 (2021 UPC)
Question: Are fluid-applied waterproofing membranes acceptable for installations receiving tile around shower drains?
Answer: Yes, IAPMO lists various waterproof membrane products as shower liners. Section 301.2, Minimum Standards, states:
“Pipe, pipe fittings, traps, fixtures, material, and devices used in a plumbing system shall be listed (third-party certified) by a listing agency (accredited conformity assessment body) as complying with the approved applicable recognized standards referenced in this code, and shall be free from defects. Unless otherwise provided for in this code, materials, fixtures, or devices used or entering into the construction of plumbing systems, or parts thereof shall be submitted to the Authority Having Jurisdiction for approval prior to being installed.”
Table 1701.1 shall be applied as indicated in the applicable referenced section.
Materials and Pipe Enclosures
Subject: Materials and Pipe Enclosures
Section: 1109.7 (2024 UMC)
Question: If tubing is not soft annealed copper, must piping comply with section 1109.7?
Answer: Yes, section 1109.7, Pipe Enclosure, applies to all piping carrying refrigerant. The intent of this section is that all refrigerant piping and tubing shall be installed so that it is not subject to damage from an external source. If the tubing is not soft annealed, then only the requirements for pipe enclosures under this section do not apply.
Soft annealed copper tubing is typically more prone to damage from external sources, hence the need for protective enclosures outlined in this section. Soft annealed copper tubing conveying refrigerant shall be enclosed in iron or steel piping and fittings, or in conduit, molding, or raceway that will protect the tubing against mechanical injury from an exterior source.
If the tubing is of a different material or not soft annealed copper, other regulations or standards may apply depending on the specific circumstances and requirements of the installation.

IAPMO
IAPMO develops and publishes the Uniform Plumbing Code®,the most widely recognized code of practice used by the plumbing industry worldwide; Uniform Mechanical Code®; Uniform Swimming Pool, Spa and Hot Tub Code®; and Uniform Solar Energy, Hydronics and Geothermal Code™ — the only plumbing, mechanical, solar energy and swimming pool codes designated by ANSI as American National Standards — and the Water Efficiency Standard (WE-Stand)™. IAPMO works with government, contractors, labor force, and manufacturers to produce product standards, technical manuals, personnel certification/educational programs and additional resources in order to meet the ever-evolving demands of the industry in protecting public health and safety.
Last modified: November 17, 2026